cross welding
英 [krɒs ˈweldɪŋ]
美 [krɔːs ˈweldɪŋ]
网络 横向焊缝
双语例句
- These cross beams increase the cost of this type of bridge, because they require handling and welding on site.
研究了一种横隔板的影响，这种横隔板应用在法国的一个典型的多跨度铁路桥梁上。 - Special for mullion V-shaped welding and cross welding cleaning.
专门用于塑料门窗中梃V型焊接及十字焊接焊缝的清理； - Cross field welding generator
交变磁场电焊发电机 - Causes of Subframe Crack and Middle Cross Beam Welding Seam Breakage and Method of Reinforcement
副车架开裂及中横梁焊缝断裂的原因和加固方法 - Cross zero stability of aluminum alloy VP PMIG welding arc
铝合金VPPMIG焊电弧过零稳定性 - Relation between strength and pitting value of cross wire projection welding
十字丝凸焊强度与下陷量的关系 - The factors of influencing strength for cross wire projection welding and for wire itself are studied on the basis of experiments.
在大量试验基础上对十字丝的凸焊强度和对母丝本体强度的影响因素进行了研究，指出下陷量是表征凸焊强度的一个重要指标。 - It showed that the weld cross section with both laser welding processes transformed from nail shape to near X shape with increase of laser power and decrease of welding speed.
结果表明，随激光功率增大和焊接速度降低，复合焊与单一激光焊焊缝的横截面形貌均由钉形向近X形转变。 - The Working Principle and Application of Cross Wall Welding
穿壁焊工作原理及应用 - It showed that the cross section of both CO_2 laser and YAG laser fully penetrated weld of titanium alloy were typically of nail shape or near X shape, which was related to heat input and laser power density in welding.
研究结果表明，在穿透焊条件下，CO2激光和YAG激光焊接钛合金焊缝都具有钉形和近X形两种典型的截面形貌。焊缝成形与焊接热输入及激光功率密度有密切联系。 - Design of I-Shaped Cross-Section Welding Composite Beam Plate Considering Yield Strength
工字形截面焊接组合梁腹板考虑屈服强度的设计 - Residual stress at ends of the welding seam of the saddle-shaped reinforcing rib of the rear axle cross member after stamping and after welding are measured respectively, and distribution and variation of residual stress are analyzed.
分别对轿车后桥横梁鞍形加强筋焊缝头部附近在冲压与焊接后的残余应力进行了测试，分析了残余应力分布与变化情况。 - Movement Scheme and Control Design of Non-standard State Pipe Cross Through Line Automatic Electric Arc Welding
非准态管子交贯线自动电弧焊的运动规划及控制设计 - Structural Characteristics of Stuffed Cross Beam on Compactors and Its Welding Process
压路机填充式横梁的结构特点及焊接工艺 - The maximum residual stress of rear axle cross member incurs at ends of the welding seam of the saddle-shaped reinforcing rib, which can result in fatigue damage.
后桥横梁鞍形加强筋焊缝头部的残余拉应力最大，可导致此处发生疲劳损伤。 - In the overall control of seam tracking, the proposed method combining the characteristics harmonic method and integral D-value method respectively control the cross slide frame and welding car.
在焊缝跟踪的整体控制中，提出了结合积分差值法和特征谐波法，分别控制十字滑架和焊接小车。 - Calculation results of the temperature field of the cross beam pipes show that the pipe lap joints exist two peaks in the adjacent weld seam after using the intermittent welding method, namely, there is the phenomenon of cyclic heating.
对横梁支架大小管焊时温度场的计算结果表明，圆管搭接接头采用断续焊焊接方式之后，在相邻两条焊缝之间出现了两个峰值点，即存在循环加热现象。 - In the paper, the main research work and the basic conclusion are as follows: 1. The three-dimensional model of tubular joint with cross weld is created, the welding residual stress is solved by using the indirect coupled method. 2.
主要的研究内容和基本结论如下：1、建立具有交叉焊缝的圆管相贯节点的三维有限元模型，采用间接耦合法求解焊接残余应力。 - The metallograph of weld cross sections is prepared after welding, and the fusion zone dimensions are obtained.
焊后制备了焊缝横截面宏观金相图片，获得了不同工艺条件下的熔合区形状与尺寸。 - The dimension of grains in different areas in the joint and the cross section pattern of FSW joint are influenced by the welding parameters.
焊接工艺参数对接头各区的晶粒尺寸以及接头截面的形貌均有较大影响。 - According to the analysis of weld depth, weld width, weld area, it can be seen that the main factor that affects weld cross section is welding current.
通过对焊缝熔深、熔宽、结合面尺寸的分析，发现焊接电流是影响复合焊接焊缝横截面尺寸的主要因素。